View SP8716_1018613.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Obsolescence Notice
This product is obsolete. This information is available for your convenience only. For more information on Zarlink's obsolete products and replacement product lists, please visit
http://products.zarlink.com/obsolete_products/
THIS DOCUMENT IS FOR MAINTENANCE PURPOSES ONLY AND IS NOT RECOMMENDED FOR NEW DESIGNS
DS 3292 -1
SP8716/8/9
520MHz LOW CURRENT TWO-MODULUS DIVIDERS
SP8716 / 40/41, SP8718 / 64/65, SP8719 / 80/81 are 50mW programmable dividers with a maximum specified operating frequency of 520MHz over the temperature range -40 C to + 85 C. The signal (clock) inputs are biased internally and require to be capacitor coupled. The output stage is of an unusual low power design featuring dynamic pull-up, and optimised for driving CMOS. The 0 to 1 output edge should be used to give the best loop delay performance.
MODULUS CONTROL UNIT OUTPUT Vcc OUTPUT 0V
1 2 3 4
8
Vcc NO CONNECTION INPUT INPUT DECOUPLING
SP 8716/8/9
7 6 5
FEATURES
DC to 520MHz Operation -40C to +85C Temperature Range Control Inputs and Outputs are CMOS Compatible
Figure : 1 Pin connections - top view
DP8, MP8
QUICK REFERENCE DATA
Supply Voltage 5.0V 0.25V Supply Current 10.5mA typ.
ABSOLUTE MAXIMUM RATINGS
Supply voltage pin 2 or 8): Storage temperature range: Max. Junction temperature: Max. clock I/P voltage: 8V -55C to +150C +175C 2.5V p-p
Vcc 8
Vcc 2
7k
SIGNAL INPUT
6 5
/P/P + 1
1.5k 1k 300
3 OUTPUT
4 0V
1 MODULUS CONTROL INPUT
Figure 2 : Functional diagram
SP8716/8/9
ELECTRICAL CHARACTERISTICS
Test conditions (unless otherwise stated):] Supply voltage: Vcc = +4/95 to 5.45V, Temperature: Tamb = -40C to +85C Value Characteristics Max. frequency Min. frequency (sinewave input) Power supply current Output high voltage Output low voltage Control input high voltage Control input low voltage Control input high current Control input low current Clock to output delay Set-up time Release time NOTES 1. Tested at 25C only 2. Guaranteed but not tested Symbol fmax fmin ICC VOH VOL VINH VINL VINH VINL tp ts tr 10 10 -0.20 28 3.3 0 (Vcc - 1.2) 1 8 1.7 0.41 Min. 520 30 11.9 Max. MHz MHz mA V V V V mA mA ns ns ns Units Conditions Input 100-280mV p-p Input 400-800mV p-p CL = 3pF; pins 2, 8 linked IL = -0.2mA IL = 0.2mA /P /P +1 VINH = 8V VINL = 0V CL = 10pF CL = 10pF CL = 10pF Notes 1 2 1 1 1 1 1 1 1 2 2 2
NOTE The set-up time ts is defined as the minimum time that can elapse between a L H transition of the control input and the next L H clock pulse transition to ensure that the /P mode is obtained. The release time tr is defined as the minimum time that can elapse between a H L transition of the control input and the next L H clock pulse transition to ensure that the /(P +1) mode is obtain
Figure 3 : Timing diagram
INPUT AMPLITUDE (mV p-p)
1000 800 600 400 200 0 30 100 200 300 400 500 FREQUENCY IN MHz 520mV
GUARANTEED * OPERATING WINDOW
280mV
*Tested as specified in table of Electrical Characteristics
Figure 4 : Typical input characteristics
SP8716/8/9
OPERATING NOTES
1. The inputs are biased internally and coupled to a signal source with suitable capacitors. 2. If no signal is present the devices will self-oscillate. If this is undesirable it may be prevented by connecting a 15k resistor from one input to pin 4 (ground). This will reduce the sensitivity. 3. The circuits will operate down to DC but slew rate must be better than 100V/,us. 4. The output stage is of an unusual design and is intended to interface with CMOS. External pull-up resistors or circuits must not be used. 5. This device is NOT suitable for driving TTL or its derivatives.
Vcc CONTROL INPUT 1 2 3 OUTPUT 4 8 7 6 5 1n 50 SIGNAL SOURCE 50 MONITOR
1n 0V
Figure 5: Toggle frequency test circuit
Figure 6 : Typical input impedance
For more information about all Zarlink products visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request.
Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE

▲Up To Search▲

Price & Availability of SP8716

	To Download SP8716 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .